Temperature-controlled switch that automatically turns equipment on or off between 0°C and 50°C.
Flush-mounted isolator switch with padlock provision for 15kW installations.
Dual contact automatic reset thermostat for high temperature industrial heating to 300 degrees.
Flush-mounted three-phase isolator with neutral for industrial power distribution control.
Flush-mounted 32A isolator switch with neutral pole for industrial electrical safety.
Temperature-activated switch for heating and cooling systems, automatic reset up to 120°C.
A blue LED indicator light that mounts flush into a 22mm hole to show when equipment is powered or operating, sealed against dust and water.
A white LED indicator light that mounts flush into a 30mm hole to show equipment status or alerts on industrial control panels.
A yellow LED indicator light that mounts flush into a 22mm hole on control panels and machines to show status or operation at 24V.
A blue LED indicator light that mounts flush into a 30mm hole on control panels and machinery to show operational status, powered by standard AC mains voltage.
A green LED indicator light that mounts flush into a 30mm panel opening and lights up to show equipment status on factory machines and control panels, running on standard factory power.
A green LED indicator light that mounts flush into a 22mm hole on control panels, rated for harsh wet and dusty environments.
A blue LED pilot light that mounts flush into a 30mm hole to show status on control panels, running on 24V power.
A red LED pilot light that mounts flush into a 30mm panel hole to show when equipment is running or in a specific state, powered by low-voltage DC or AC current.
An orange LED indicator light that mounts flush in a 30mm hole and runs on 19.2–30V DC or 21.6–26.4V AC, used on control panels and machinery to show status.
A bright orange LED pilot light that mounts flush into a 30mm hole on control panels to show when equipment is running or powered on.
A red LED pilot light that mounts flush into a 30mm hole on control panels to show when equipment is running or in an alarm state.
A white LED indicator light that mounts flush into a 30mm panel hole to show operational status of machinery and control systems.
Flush-mounted electrical isolator switch rated 10A, 3kW, for machinery and panel safety disconnect.
A white LED indicator light that mounts flush into a 22mm panel opening, rated IP65 for dusty or damp environments, powered by 24V AC or DC.
A green LED indicator light that mounts flush into a 30mm hole on control panels to show status or system operation in industrial machinery and electrical cabinets.
A white LED indicator light that mounts flush into a 30mm hole on control panels and machinery, powered by standard AC voltage, to show equipment status.
A red LED indicator light that mounts flush into a 30mm hole on control panels and machinery to show operational status, powered by standard industrial AC voltage.
A white LED indicator light that mounts flush into a 30mm hole on control panels and machinery to show when equipment is running or powered on, rated for 100-132V AC.
A blue LED indicator light that mounts flush into a 30mm hole on control panels and machinery to show status, powered by 100–132V AC electricity.
A white LED indicator light that mounts flush into a 30mm hole to show status or signal on industrial control panels and machinery.
A blue LED pilot light that mounts flush into a 30mm hole on control panels and electrical cabinets to show when equipment is powered or operating.
An orange LED pilot light that mounts flush into a 30mm hole on control panels to indicate power or status in industrial equipment.
A red LED indicator light that mounts flush on control panels to show equipment status or alarm conditions, operating on low DC voltage.
A red LED indicator light that mounts flush into a 30mm hole on control panels and machinery to show operational status or alerts, powered by standard AC mains voltage.
A red LED indicator light that mounts flush into a 30mm hole on control panels and machinery to show operating status or alert conditions, powered by 100–132V AC electricity.
A green LED pilot light for industrial control panels that mounts flush into a 30mm hole and lights up when powered between 195V and 264V AC, commonly used to show equipment status.
Orange LED indicator light that mounts flush into a 30mm hole to show equipment status or warnings on control panels and machine interfaces.
A green LED indicator light that mounts flush into a 30mm hole on control panels and machine enclosures to show status or operating conditions.